Shree Enterprises

Testex Snap Gauge is used for the measurement of the surface profile after blasting when taken with Testex Tape / Replica Tape / Press-O-Film.

Testex Tape or Press O Film offers a simple and very accurate method of measuring blasted profiles. It can produce virtually exact replicas of the blasted surface profile, which can be measured using a snap gauge.

Testex snap gauge is simple hand held operation. Place the Testex film or press o film firmly on the blasted surface, apply moderate pressure with the burnishing tool, the replica has now been taken and can be measured using the textex snap gage

This contamination can be tested quickly and simply using the Bresle Test Kit. This kit has advantage over portable units. Test can be quickly performed at site, shop floor and plants. The Bresle Patch is attached to the surface; the distilled water is injected with a syringe then extracted, repeat ten cycles of injecting and extracting then measure with the Conductivity Meter. Compact conductivity meter will measure the quantity of salts in μg/cm2 (ppm) and mg/m2. Bresle test complies with ISO 8502-6, which relates to the extraction of soluble contaminants and ISO 8502-9, which relates to the conduct metricdetermination of soluble salts. Calibration Certificates traceable are available for the Conductivity Meter in the kit.The Bresle Test Kit is supplied with 50 Bresle Patches, 1 Conductivity Meter, Calibration Solutions, 5x5ml Syringes, 25mlBeaker and 250ml Distilled Water. Additional Bresle Patches can be purchased to carry out further tests using this kit.Part Numbers: BTK-001 Bresle Test Kit BTK-002 Bresle Patches (Pack of 50 Nos.) 

Offers Bresle Patches For Bresle Test Kit. The Bresle Test Patches to TestFor Chloride and Soluble Salt Surface Contaminants on Blasted Surfaces InCompliance With ISO 8502-6 and ISO 8502-9

Easy To Use, Pour 10mls Of Distilled Water Into The Beaker And Determine The Conductivity UsingThe Conductivity Meter. Take A Bresle Patch and Apply To the Test Surface. Fill The Syringe With2.5mls Of Test Water And Insert Through The Adhesive Foam Into The Test Chamber. Inject TheContents, Then Extract Back Into The Syringe. Repeat Ten Cycles Of Injecting And Extracting ThenTransfer The Test Water Back Into The Beaker. Measure The Test Water With The Conductivity MeterAnd Deduct The Initial Conductivity Reading From The Result. Test Results Are Based On Expression OfResults Are Based On Section 7 Of ISO 8502-9 And Nace SP0508 Specification. Multiply The ReadingsBy 0.1 To Give The Quantity Of Salts In mg/Cm² Also Known As Ppm, Or By 1 For The Quantity Of SaltsMg/M². Multiply mg/m2 Reading By 0.60 To Obtain the Concentration of Chloride Level In mg/m2.Multiply mg /Cm2 Reading by 0.06 to Obtain the Concentration of Chloride Level in mg /Cm2.

The Maximum Permissible Surface Density Of Salts On The Steel Surface Prior To Surface TreatmentDepends On The Type Of Paint To Be Applied And What The Finished Material Or Product Is To BeUsed For. Surface Treatment Specifications Must, Therefore, State The Highest Permissible SurfaceDensity Of Salts For Each Particular Application.

• Dust Tape Kit (Complete with dust comparator display board, dust assessment plate, illuminated magnifier (10X) and adhesive tape in case
• Package Contains: 1 Unit as shown in image
• Longer Life
• Best Finish

Product description
Caltech Engineering Services introduces ISO 8502-3 Dust Tape Test Kit. Dust Tape Test Kit or dust evaluation kit or dust test kit is useful for painting inspection surface preparation. Recommended dust test kit according to ISO 8502-3. Dust Tape Test kit allows assessment of the quantity and size of dust particles on surfaces prepared for painting. Dust on blast cleaned surfaces can reduce coating adhesion, leading to premature coating failure and sub-standard coating finish Complete Dust Test Kit is supplied with Illuminated magnifier (10x, 2 batteries, and adhesive tape to specification, comparator display board, dust assessment plate and operating manual). Caltech also manufactures spring loaded dust tape roller which can be used along with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust. Supplied in a case to carry at site or shop to evaluate and assess surface cleanliness on the spot.